October 27, 2026

A presswood pallet plant buys tonnage and still loses output at the die exit: a manual take-out post cannot be timed to the press open and close signals, so a 1250 to 1600 ton press waits on a person every cycle, line OEE drops and unit cost carries the delay plus one operator per press on every shift. AutoG is the automatic pallet take-out robot from EMP, delivered as the press exit take-out and automatic stacking cell on a presswood pallet production line: the take-out motion is coordinated with the press open and close signals on the line PLC, a vacuum suction cup end effector takes the freshly pressed pallet at about 80 degrees Celsius without a cooling wait, transfers it by vacuum suction and stacks it where it leaves the gripper, and one arm alternately tends two presses as a dual press tending cell, so press exit manning is set per press pair instead of per press. Limits are stated plainly: rated load, working radius, repeat accuracy, suction and vacuum configuration, footprint, power and air demand, control interface detail and robot body source stay project confirmed; the 1250 to 1600 ton range, the four to five minute MDI cycle, continuous running and the replacement of about two take-out operators are supplier statements; the 80 degrees Celsius figure is quoted from the EMP equipment centre description; no ROI, payback or hourly output is claimed; and the unit is the press exit take-out and stacking device on a presswood pallet line, not the press itself, not the crush, dry or glue stage and not an independently running line.

A presswood pallet plant can run its hot press 24 hours a day and still be unable to run the station in front of it, because the press exit needs one take-out operator per 1250 to 1600 ton press on every shift, and the night shift is where that arrangement breaks: coverage is covered by overtime rather than by plan, a manual take-out is not synchronised to the press open and close signals so the press waits on a person, and the duty itself is a pallet leaving the mold at about 80 degrees Celsius with a grooved surface and hot MDI adhesive gas. AutoG is the automatic pallet take-out robot from EMP, delivered as the press-exit take-out and automatic stacking cell on a molded wood pallet line: a vacuum suction cup end effector takes the freshly pressed pallet on the press open signal, transfers it without a cooling wait and stacks it where it leaves the gripper, with one arm alternately tending two presses as a dual-press tending cell, so press-exit manning is set per press pair instead of per press and per shift. Limits are stated plainly: rated load, working radius, repeat accuracy, suction and vacuum configuration, footprint, power and air demand, control interface detail and robot body source stay project-confirmed; the 1250 to 1600 ton range, the four to five minute MDI cycle, continuous running and the replacement of about two take-out operators are supplier statements; the 80 degrees Celsius figure is quoted from the EMP equipment centre description; no payback, ROI or hourly output is claimed; and the unit is the press-exit take-out and stacking device on a presswood pallet line, not the press itself, not the crush, dry or glue stage and not a stand-alone line.

On a molded wood pallet line the press exit is the one station that still asks a person to stand in it: an operator reaches into the open die for a pallet that leaves the mold at about 80 degrees Celsius, one operator per 1250 to 1600 ton press, on every shift, in a bay that carries radiant heat, airborne wood fibre and the gases a hot MDI adhesive releases during pressing. AutoG is the automatic pallet take-out robot from EMP, delivered as the press-exit take-out and automatic stacking cell on a presswood pallet production line: on the press open signal a vacuum suction cup end effector takes the freshly pressed pallet, transfers it without a cooling wait and stacks it where it leaves the gripper, with one arm alternately tending two presses as a dual-press tending cell, so the take-out position is unoccupied from the open signal to the close signal and manning is set per press pair instead of per press. Limits are stated plainly: rated load, working radius, repeat accuracy, suction and vacuum configuration, footprint, power and air demand, control interface detail and robot body source stay project-confirmed; the 80 degrees Celsius figure is quoted from the EMP equipment centre description; the 1250 to 1600 ton range, the four to five minute MDI cycle, continuous running and the replacement of about two take-out operators are supplier statements; no ROI, payback, hourly output, medical conclusion or exposure-limit compliance claim is made; and the unit is the press-exit take-out and stacking device on a presswood pallet line, not the press itself, not the crush, dry or glue stage and not a stand-alone line.

A presswood pallet production line is automated up to the die and then hands the last metre back to a person: at the press exit an operator reaches into the open die for a pallet that leaves the mould at about 80 degrees Celsius, one operator for every 1250 to 1600 ton press, on every shift, inside the press danger zone where a mis-command is a crushing or severing accident rather than a near miss. AutoG is the automatic pallet take-out robot from EMP, delivered as the press-exit take-out and automatic stacking cell on a presswood pallet production line: a six-axis articulated arm with a vacuum suction cup end effector takes the freshly pressed pallet on the press open signal, transfers it without a cooling wait, stacks it where it leaves the gripper and alternately tends two presses as a dual-press tending cell, so the take-out position is unoccupied from the open signal to the close signal and press-exit manning is set per press pair instead of per press. Limits are stated plainly: rated load, working radius, repeat accuracy, suction and vacuum configuration, footprint, power and air demand, control interface detail and robot body source stay project-confirmed; the 80 degrees Celsius direct take-out figure is quoted from the EMP equipment centre description; the 1250 to 1600 ton range, the four to five minute MDI press cycle, continuous running and the replacement of about two take-out operators are supplier statements; no ROI, payback or hourly output is claimed; and the unit is the press-exit take-out and stacking device on a molded wood pallet line, not the press itself, not the crush, dry or glue stage and not a stand-alone line.

A molded pallet plant running more than 200,000 blocks a day, 24 hours and seven days, carries a take-out crew that scales with tonnage rather than with cost: one operator per 1250 to 1600 ton press, every shift, reaching for a pallet that leaves the die at about 80 degrees Celsius, then lifting it onto a stack by hand. The pallet has to be visibly cheaper than a sawn timber one, and the exit is the one station where every extra thousand units buys more people. AutoG is the automatic pallet take-out robot from EMP, delivered as the press-exit take-out and automatic stacking cell on a presswood pallet production line: it takes the freshly pressed pallet on the press open signal, transfers it by vacuum suction without a cooling wait, stacks it where it leaves the gripper and alternates across two 1250 to 1600 ton presses, so press-exit manning is set per press pair instead of per press and rising volume no longer buys rising headcount. Limits are stated plainly: rated load, working radius, repeat accuracy, suction and vacuum configuration, footprint, power and air demand, control interface detail and robot body source stay project-confirmed; the 1250 to 1600 ton range, the four to five minute MDI cycle, the 24-hour running statement and the replacement of about two take-out operators are supplier statements; the 80 degrees Celsius figure is quoted from the EMP equipment centre description; no ROI, payback or hourly output is claimed; and the unit is the press-exit take-out and stacking device on a molded wood pallet line, not the press itself, not the crush, dry or glue stage, not a general case palletizer and not a stand-alone line.

A molded wood pallet producer that insists on a German, Austrian or Italian press body while its price strategy demands a lower unit cost has one variable it can move without touching the forming technology: the press exit. AutoG is the automatic pallet take-out robot from EMP, specified as the press-exit take-out and automatic stacking cell on a presswood pallet production line, taking the freshly pressed pallet at about 80 degrees Celsius through a vacuum suction gripper without a cooling wait and stacking it where it leaves the gripper, with one arm alternately tending two 1250 to 1600 ton presses as a dual-press tending cell. That is the cost-optimised position: the press body, the hydraulics, the mold and the line PLC stay as specified, and the hot, repeated, least-differentiated take-out duty moves off people, so take-out capex and press-exit manning are set per press pair rather than per press. Limits are stated plainly: rated load, working radius, repeat accuracy, suction and vacuum configuration, footprint, power and air demand, control interface detail and robot body source stay project-confirmed; no ROI, payback or hourly output is claimed; the 80 degrees Celsius figure is quoted from the EMP equipment centre description; the 1250 to 1600 ton range, four to five minute MDI cycle, continuous running and two-operator replacement are supplier statements; and the unit is the press-exit take-out and stacking device on a molded wood pallet line, not the press itself, not the crush, dry or glue stage and not a stand-alone line.

A molded pallet plant that has proven wood fibre takes its first real material risk at the press exit, not at the mixer: a coconut husk pallet can differ from a wood-fibre pallet in formed density, die-exit temperature and deck surface, so a take-out head and cycle sized on wood fibre is an assumption rather than a specification. AutoG is the automatic pallet take-out robot from EMP for hydraulic press pallet take-out on a presswood pallet production line, taking the freshly pressed pallet on the press open signal, transferring it by vacuum suction and stacking it where it leaves the gripper, with one arm alternating across two 1250 to 1600 ton presses as dual-press tending, so press-side manning is set per press pair. The suction cup arrangement, grip pattern and take-out cycle are validated on the customer’s own coconut husk pallet in a sample trial: die-exit temperature is measured at more than one deck point, pallet form and groove geometry are logged, and vacuum hold is tested on the hot surface. Limits are stated plainly: EMP’s published 80 degrees Celsius direct take-out figure belongs to presswood pallets and is not carried over to coconut husk before that trial, rated load, working radius, repeat accuracy, suction and vacuum configuration, footprint, power and air demand, robot body source and control interface stay project confirmed, the 1250 to 1600 ton range and the 4 to 5 minute MDI press cycle are supplier statements, no ROI, payback or hourly output is claimed, and the unit is the press-exit take-out and stacking device on a molded wood pallet line, not the press, not the crush, dry or glue stage and not a stand-alone line.

A presswood pallet group that grows by copying its validated line cannot hand its fibre recipe, moisture setpoint or press curve to a machine builder, yet every copy inherits the same staffed press exit: one operator per 1250 to 1600 ton press, every shift, in every plant, reaching for a pallet that leaves the mold at about 80 degrees Celsius and then lifting it onto a stack by hand. AutoG is the automatic pallet take-out robot from EMP, delivered as one turnkey scope with the hydraulic press, automatic stacking and the line PLC, where a six-axis arm with a vacuum suction cup end effector takes the freshly pressed pallet on the press open signal, transfers it without a cooling wait and stacks it where it leaves the gripper, with one arm alternately tending two presses on the same Siemens or Mitsubishi line control. The customer’s process parameters stay the customer’s: they enter the integration layer as project inputs, not as something the supplier is asked to reverse engineer. Limits are stated plainly: rated load, working radius, repeat accuracy, suction and vacuum configuration, footprint, power and air demand, control interface detail and robot body source stay project-confirmed, the 1250 to 1600 ton range, four to five minute MDI cycle, continuous running and two-operator replacement are supplier statements, no ROI, payback or hourly output is claimed, and the unit is the press exit take-out and stacking device on a presswood pallet production line, not the press itself, not the crush, dry or glue stage and not a stand-alone line.

A molded wood pallet plant selling into European and Australian lanes keeps its process controlled right up to the die, then hands the last metre to a person: a pallet at about 80 degrees Celsius is taken out and stacked by hand, two operators on two 1250 to 1600 ton presses, and every pick is a slightly different pose, so a corner is dragged, one stack is built true and the next leans. AutoG is the automatic pallet take-out robot from EMP that takes the freshly pressed pallet on the press open signal, transfers it by vacuum suction and stacks it where it leaves the gripper, with one arm alternating across two presses as a dual press tending cell, so the pick path and the stack repeat instead of varying with the operator on shift. Limits are stated plainly: rated load, working radius, repeat accuracy, suction and vacuum configuration, footprint, power and air demand, robot body source and control interface stay project confirmed, no ROI, payback or hourly output is claimed, the 80 degrees Celsius figure is quoted from the EMP equipment centre description, the 1250 to 1600 ton range and the 4 to 5 minute MDI cycle are supplier statements, the 1.5 to 2 t dynamic and 5 to 8 t static load references belong to the pallet and are confirmed per project rather than being an AutoG certificate, and the unit is the press exit take-out and stacking device on a presswood pallet line, not the press itself, not the crush, dry or glue stage and not a stand-alone line.

A presswood pallet group that competes on price grows by copying its line, and every copy inherits the same press-exit pattern: one take-out operator for every 1250 to 1600 ton press, on every shift, in every plant, so an item that is rarely reviewed on the expansion plan scales with installed presses and with site count while the unit price keeps falling. AutoG is the automatic pallet take-out robot from EMP that pairs one vacuum suction arm with two presses on their open signals, takes the freshly pressed pallet at about 80 degrees Celsius without a cooling wait and stacks it where it leaves the gripper, so press-exit manning is set per press pair instead of per press and unit capacity take-out capex per press station drops without a turnkey package for every press. Limits are stated plainly: rated load, working radius, repeat accuracy, suction and vacuum configuration, footprint, power and air demand, PLC detail and robot body source stay project-confirmed, the 1250 to 1600 ton range, four to five minute cycle, continuous running and two-operator replacement are supplier statements, no ROI, payback or hourly output is claimed, and the unit is the press-exit take-out device on a molded wood pallet line, not the press itself, not the crush, dry or glue stage and not a stand-alone line.